Earthquake 26750 Manuel d'utilisateur télécharger pdf (Page 12)

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-512

Operator's Manual

VECTOR™ Compact Tiller

PRESTART INSPECTION

1. Make sure all safety guards are in place and all nuts and bolts

are secure.

2. Check oil level in engine crankcase. See your engine manual

for procedure and specications.

3. Inspect air cleaner for cleanliness. See your engine manual

for procedure.

4. Check the fuel supply. Fill the fuel tank no closer than 1

inch from top of tank to provide space for expansion. See

your engine manual for fuel recommendations.

5. Be sure spark plug wire is attached and spark plug is

tightened securely.

6. Check depth regulator lever position.

7. Examine underneath and around engine for signs of oil or

fuel leaks.

8. Inspect fuel hoses for tightness and fuel seepage.

9. Look for signs of engine damage.

10. Remove excessive debris from muer area and recoil starter.

STARTUP

The controls required to start and run the rototiller are located

on the engine.

The throttle speed control is located above the pull-start recoil

and is indicated by a rabbit for FAST and a turtle for SLOW. The

choke lever is located above the air cleaner cover. The On/O

switch is located on the side of the blower housing closest to

the recoil pull handle.

A more detailed description of engine operation and all related

precautions and procedures can be found in the engine

manufacturer’s manual that accompanies each tiller.

COLD STARTS

1. Turn the On/O switch to the ON position

2. Move choke lever to full choke position.

3. Move throttle lever to half way between the SLOW position

and the FAST position.

4. Pull starting rope out slowly one time and allow to return

normally.

5. Pull starting rope out rapidly, and allow rope to return

normally. Repeat until engine starts.

6. When engine starts, gradually move choke lever to run

position and increase throttle speed to the FAST position for

tilling.

IMPORTANT

ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL. YOU

MUST ADD ENGINE OIL BEFORE STARTING ENGINE.

PRACTICE OPERATING THE CONTROLS AND TILLER

WITH TINES OUT OF GROUND BEFORE BEGINNING TO

TILL. IT IS IMPORTANT THAT YOU KNOW HOW TO USE

THE TILLER PROPERLY, KEEP CONTROL AT ALL TIMES,

STOP THE TINES AND WHEELS FROM TURNING, AND

STOP THE ENGINE IF NECESSARY. IF YOU DO NOT KNOW

HOW TO DO THESE THINGS, READ THE CONTROLS AND

SAFETY SECTIONS BEFORE PROCEEDING.

CAUTION

PLEASE DO NOT START YOUR TILLER UNTIL YOU

HAVE READ THE MANUAL THAT CAME WITH YOUR

ENGINE, AND THE SECTIONS IN THIS MANUAL TITLED

CONTROLS AND SAFETY. IF YOU HAVE READ THESE,

FOLLOW THE STEPS IN THE STARTUP SECTION TO

START YOUR TILLER. ALWAYS PERFORM THIS PRE

START CHECKLIST BEFORE STARTING THE ENGINE.

IMPORTANT

GASOLINE IS HIGHLY FLAMMABLE AND MUST BE

HANDLED WITH CARE. NEVER FILL THE TANK WHEN

THE ENGINE IS HOT OR RUNNING. ALWAYS MOVE

OUTDOORS TO FILL THE TANK.

TEMPERATURE OF MUFFLER AND NEAR BY AREAS MAY

EXCEED 150° F. AVOID THESE AREAS.

DO NOT MOVE CHOKE CONTROL TO CHOKE TO STOP

ENGINE. BACKFIRE OR ENGINE DAMAGE MAY OCCUR.

TO STOP THE ENGINE AT ANY TIME, TURN THE ON/OFF

SWITCH TO THE OFF POSITION. TO STOP TINES AT ANY

TIME, RELEASE DRIVE SAFETY CONTROL LEVER TO THE

NEUTRAL POSITION.

ALWAYS RELEASE DRIVE SAFETY CONTROL LEVER TO

THE NEUTRAL POSITION AND TURN ENGINE OFF BEFORE

ADJUSTING THE DEPTH OF THE REGULATOR LEVER.

RESTARTING A WARM ENGINE

Restarting an engine that is already warm from previous running

does not normally require use of the choke.

1. Turn the On/O switch to the ON position.

2. Move throttle lever to half way between SLOW and FAST.

3. Pull starting rope out rapidly until engine starts. Allow rope

to return normally. Repeat until engine starts.

4. Adjust throttle speed to the FAST position for tilling.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 71 72

Commentaires sur ces manuels

Pas de commentaire

Earthquake 26750 Manuel d'utilisateur Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Machines spéciales Earthquake 26750