EarthQuake CRT series Manuel de l'opérateur télécharger pdf (Page 10)

Operator’s Manual

Front Tine Tiller 3365 Series

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

For model 3365PSCE only.

The controls required to start and run the rototiller are located on the

handle.

A more detailed description of engine operation and all related

precautions and procedures can be found in the engine manufacturer’s

manual that accompanies each tiller.

COLD STARTS

1. Move the throttle control to the FAST position.

2. Pull starting rope out slowly one time and allow to return normally.

3. Pull starting rope out rapidly and allow rope to return normally.

4. Operate engine in the FAST position.

RESTARTING A WARM ENGINE

Restarting an engine that is already warm from previous running does

not normally require use of the choke.

1. Move throttle lever to FAST position.

2. Pull starting rope out rapidly until engine starts. Allow rope to return

normally. Repeat until engine starts.

3. Adjust throttle speed to FAST for best tiller action.

OPERATING SPEED

For normal tilling, set the throttle lever to FAST.

SHUTTING DOWN

For models 3365B, 3365CE and 3365PS only.

To stop the engine at any time, move the throttle control to the OFF

position. To stop wheels and tines at any time, release the drive safety

control to the NEUTRAL position.

ADDITIONAL SAFETY INFORMATION CE UNITS ONLY

The 3365CE rototiller unit has been tested and veried to be within the

acceptable level of noise range for CE compliance at 95dB L

For the health and safety of the consumer it is recommended that this

product be used for no more than 2 consecutive hours in any given 12

hour period.

WARNING

DANGER

ENGINE AND SURROUNDING PARTS BECOME EXTREMELY

HOT DURING NORMAL USE AND WILL CAUSE SERIOUS BURN

INJURIES IF TOUCHED BEFORE THE ENGINE HAS COOLED.

ALLOW ENGINE TO COOL COMPLETELY BEFORE

TOUCHING THESE HOT SURFACES.

ALWAYS KEEP HANDS AND FEET CLEAR OF ROTATING

MACHINE PARTS.

EXTREME CAUTION MUST BE TAKEN IN SELECTING TILLING

DEPTH. IF YOU ATTEMPT TO TILL TOO DEEPLY FOR SOIL

CONDITIONS THAT IS, WITH THE DRAG STAKE IN TOO

HIGH OF A POSITIONLOSS OF CONTROL COULD RESULT.

IF REMOVING MATERIAL FROM THE TINES BY HAND, STOP

THE ENGINE AND REMOVE SPARK PLUG WIRE FIRST.

Model 2006/42/EC

Operator Ear

(dBA)

2006/42/EC

Sound Power Level

(dBA)

2006/42/EC

Hand/ArmVibration

Max m/s

2006/42/EC

Vibration Time Limit

3365PSCE

Front Tine Tiller

86 98 3.3 EAV= 4 h. 35 min.

ELV= 18 h. 22 mins.

SoundlevelstestinaccordancewithISO3744andISO11201-Grade2(Engineering)Method.Readingstakenwithengineatfull

throttle.EAV=ExposureActionValue;ELV=ExposureLimitValue

For model 3365PSCE only.

To shut the engine o, push the throttle control lever all the way forward.

Turn the fuel shuto valve to the CLOSED position.

TILLING

1. Adjust the depth regulator lever to desired tilling depth.

NOTE: Raise depth regulator lever up one hole at a time, testing

tiller operation after each raise. Raising depth regulator lever too

high can result in loss of control of tiller!

2. Move the throttle control to FAST.

3. Place the tiller in motion by pushing down on the drive safety control

lever;thiswillengagethetines.

Sound and Vibration Levels

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 23 24

Commentaires sur ces manuels

Pas de commentaire

EarthQuake CRT series Manuel de l'opérateur Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Mini-faucheuses EarthQuake CRT series