EarthQuake CRT series Manuel de l'opérateur télécharger pdf (Page 6)

Operator’s Manual

Front Tine Tiller 3365 Series

Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 CST

UNPACKING AND ASSEMBLY

UNPACK TILLER AND ASSEMBLE

1. Open top of carton and remove handlebar assembly.

Find parts packet. Parts packet for 3365B/3365CE contains:

6 - 5/16-18 x 1-3/4” bolts

6 - 5/16” spring lock washers

2 - hand knobs

4 - locknuts

2 - hairpins

 2-12mmatwashers

1 - detent pin

Parts packet for 3365PS/3365PSCE contains:

2 - 3/8-16 x 1” bolts

2 - 3/8-16 biway locknuts

2 - 5/16-18 x 1” bolts

4 - 5/16-18 x 1-3/4” bolts

6 - 5/16” spring lock washers

2 - hand knobs

4 - 5/16” locknuts

2 - hairpins

 2-12mmatwashers

1 - detent pin

3. Cut open end of carton and remove machine:

a. Install wheelson each endof axle; installwashers ontoaxle

againstwheels;inserthairpinsintoholesinaxletokeepwashers

and wheels in place.

b. Assemble tines to unit, inside tines rst. Sharp edge of tine will

be away from operator at top, or face down at front of machine.

c. Outside tines have two positions- wide 21” and narrow 16”. For

narrow width, assemble with short side of tine holder pipe to-

wards center of machine.

d. For wide width, move the left tine to the right side and right tine

to the left side. Assemble with the long half of tine pipe towards

machine.

e. Slide the top handle of handlebar over the lower loop. Put

5/16-18x 1-3/4”bolts throughboth holesfrominsideout;

put on 5/16” spring lock washers and tighten with hand knobs.

Model 3365PS will use 3/8-16 x 1” bolts with nuts and 5/16-18

x 1” bolts with hand knobs. See the parts breakdowns for more

information.

f. Check upper and lower jam nuts for tightness. See “Controls”

section for belt tension adjustment instructions.

g. Add and check engine oil.

INSTALL DEPTH REGULATOR LEVER

1. Install the depth regulator lever through hole in bracket from the

bottom up with curve to rear of unit and secure with detent pin.

FILL ENGINE CRANKCASE

1. Add oil according to engine manual. Do not overfill. Use a

clean, high quality detergent oil. Use no special additives with

recommended oils. Do not mix oil with gasoline. Oil level must

be full. Check the oil level by checking the engine’s oil dipstick if

provided, or by removing oil ll plug. Oil level should be up to the

bottom of the ll plug opening.

2. Always check oil level before starting engine. Refer to engine manual

for capacity and type of oil to use.

upper

handlebar

CAUTION

DO NOT TRY TO LIFT THE ROTOTILLER FROM THE CARTON.

IMPORTANT

THE RIGHT AND LEFT SIDES OF YOUR RO

TOTILLER ARE DETERMINED FROM THE

OPERATING POSITION AS YOU FACE THE

DIRECTION OF FORWARD TRAVEL.

ENGINE IS SHIPPED FROM FACTORY WITH

OUT OIL. YOU MUST ADD ENGINE OIL BE

FORE STARTING ENGINE.

NARROW TINE WIDTH

WIDE TINE WIDTH

lower

handlebar

loop

hand knob

depth

regulator

lever

detent pin

L R

1 2 3 4 5 6 7 8 9 10 11 ... 23 24

Commentaires sur ces manuels

Pas de commentaire

EarthQuake CRT series Manuel de l'opérateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Mini-faucheuses EarthQuake CRT series